Rupal Jindal

RUPAL JINDAL #981/2, Bhindian Street Patiala, Punjab – 147001 (+91)- | (+91)-- Mechanical Engineer with nearly 8 years of experience in Process Planning, Engineering & Development for Automotive, Off-highway, Defence, Pumps and Electronics products in Mass and Batch production. Possessing a B.E. in Mechanical Engineering and a good knowledge of Processes, Raw Materials, Tooling and Machines. Looking for an opportunity in a reputed organization that promotes personal growth and leverages my knowledge and experience. Professional Experience P.A.PINIONS, dharampur, hp Manager, April 2017 – June 2019 Performed Costing for RFQs & existing parts of Indian and International Customers Interacted with Customers regarding any issues/queries related to NPD and existing parts Coordinated the development activities and managed documentation of more than 2,000 parts Studied RFQs, discussed queries and suggested ideas to Customer as per application Ensured RoHS/REACH compliance of the parts and their packaging as per Customer Instilled awareness to 4 Process Engineers regarding various standards and related basics Trained 2 Production Line in-charges to program for Automatic Tool Life Monitoring Updated documentation of the department for compliance with ISO 9001:2015 Guided the PPAP/APQP documentation for parts as per Customer requirement CNC AUtomotive, bengaluru, kA Manager, September 2015 – February 2017 Enhanced Tool life for an operation by over 50%, a part of CIP to reduce inventory Reduced Tool cost by over 20% by developing an Alternate vendor for an existing insert Visited the Customer site to address concerns and understand application requirements Established Packaging of 2 parts for their dispatch Planned and ordered Tooling for production and development parts Ensured ISO/TS 16949 and VDA 6.3 conformance of documentation avtec LTD., hosur, tn Manager, June 2015 – September 2015 Planned Process and Tooling for Planet Wheel Carrier and Drive Shaft projects Reduced Cycle time by over 30%, ensuring the same quality of parts Developed 4 running parts on alternate machines to improve Asset Sweating Trimmed down Tool cost by more than 50% for an operation Trained 3 machine operators regarding Tool holders and Inserts for their Skill Development Addressed Production/Quality issues within the plant Assistant Manager, July 2011 – May 2015 Achieved Tool life improvement by more than 80% through optimization of Cutting parameters and introduction of Surface treatment Reduced Set-up time by over 5 minutes by eliminating Tool change during set-up changeover Achieved Tool cost reduction by at least 40% by standardizing 2 inserts; a part of VA/VE Performed TPM activities like Cycle time study & Root cause analysis Created Instruction sheets, Tool setup sheets and Work instructions for new and running parts Developed an Interactive routing for operators to give step-by-step Visual guidance to them Education thapar uNiversity, patiala, pb Full time, 2007–11 Graduated with B.E. in Mechanical Engineering Additional Skills Certified Metal Cutting Application Engineer from Kennametal Involved in manufacturing of parts made from Steel, Cast Iron, Aluminium alloy, Stainless Steel, Tungsten alloy, Copper, Brass, PEEK, POM, etc. Skilled in operating CNC Turning Centre (Lathe) and Vertical Turret Lathe (VTL) Capable of handling Vertical & Horizontal Machining Centre (VMC & HMC) Experienced with CNC Sliding Headstock machine (Swiss Automatic Lathe) Acquainted with Hydromat, Single-spindle Automat & Multi-spindle Automat Well-versed in various Tooling - Coated & Uncoated Inserts (Turning & Milling – Carbide, Ceramic, Cermet, CBN & PCD), Tool holders (Turning & Milling), Adaptors (Milling), etc. Practically experienced in CNC programming for Turning & Milling Competent in major Machine Controllers (Siemens, Fanuc, MAPPS, Mazatrol, etc.) Familiar with Casting, Forging, PDC, LPDC & GDC parts and/or process Cognizant of various Surface Treatment processes like Anodizing, Blackening, Phosphating, Plating, Passivation, Heat treatment (Hardening, Tempering, Case carburizing, Nitriding) Exposed to Gear cutting operations i.e. Hobbing, Shaping, Shaving & Grinding Aware about various Packing materials & applications Knowledgeable about Material Handling methods & practical implications Accustomed to Pro-E, AutoCAD, ERP, SAP, OpenOffice and MS-Office Able to deliver more than the expectations from a task